Volume 4, Issue 2, April 2019, Page: 21-29
Numerical Simulation of Centrifugal Pump and Effect of Impeller Geometry on Its Performance
Mohamed Hassan Gobran, Mechanical Power Engineering Department, Faculty of Engineering, Zagazig University, Zagazig, Egypt
Mostafa Mohamed Ibrahim, Mechanical Power Engineering Department, Faculty of Engineering, Zagazig University, Zagazig, Egypt
Ramy Elsayed Shaltout, Mechanical Power Engineering Department, Faculty of Engineering, Zagazig University, Zagazig, Egypt
Mahmoud Ahmed Shalaby, Jushi Egypt for Fiberglass Industry S.A.E, Port Said, Egypt
Received: Apr. 2, 2019;       Accepted: May 15, 2019;       Published: Jun. 4, 2019
DOI: 10.11648/j.eas.20190402.11      View  26      Downloads  16
Abstract
In the presented paper, the effect of impeller geometric parameters on the performance of centrifugal pump has been investigated. This study was performed for different flow rates and rotational speeds, allowing to obtain the performance curve for the centrifugal pump. Three dimensional computational fluid dynamic simulation of the impeller and volute for a centrifugal pump has been performed using ANSYS CFX software (a high-performance computational fluid dynamics software tool that delivers reliable and accurate solutions). The pump has an outside impeller diameter of 205 mm, impeller outlet width of 16 mm, rotational speed 1450 rpm, seven impeller blade and a specific speed of 28. By increasing the impeller outer diameter and outlet width, both net head and power consumed are increased. In addition, it was noticed that the best efficiency point (BEP) was achieved at volume flow rate higher than design flow rate. The performed simulations indicated that; by changing the impeller outer diameter from 200 mm to 210 mm, the flow rate of BEP increases about by 14.7%. By changing the impeller outlet width from 14 mm to 18 mm, the flow rate of BEP increased by about 9%, and the efficiency of BEP reduced by approximately 0.5%. It was also noticed that, increasing the rotational speed will cause an increase in the net head and consumed power. An increase of 13.8% for the flow rate of BEP was observed when changing the rotational speed from 1400 rpm to 1500 rpm, with the same BEP.
Keywords
Centrifugal Pump, Impeller Diameter, Rotational Speed, Impeller Width
To cite this article
Mohamed Hassan Gobran, Mostafa Mohamed Ibrahim, Ramy Elsayed Shaltout, Mahmoud Ahmed Shalaby, Numerical Simulation of Centrifugal Pump and Effect of Impeller Geometry on Its Performance, Engineering and Applied Sciences. Vol. 4, No. 2, 2019, pp. 21-29. doi: 10.11648/j.eas.20190402.11
Copyright
Copyright © 2019 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
K. Rajput, "Textbook of fluid mechanics and hydraulic machines", Revised Edition, S.chand 2010.
[2]
W. Li and Hu ZM, "An experimental study on performance of centrifugal oil pump", Fluids Mach 1997, 25(2), 3–7.
[3]
W. Li and D. Deng, "Reynolds number of centrifugal oil pumps and its effects on the performance", Pump Technol 1999 (3), 3-10.
[4]
W. Li, "Effects of viscosity of fluids on centrifugal pump performance and flow pattern in the impeller", International Journal of Heat and Fluid Flow, 2000, 2(21), 207–212.
[5]
W. Li, " Numerical study on behavior of a centrifugal pump when delivering viscous oils – Part 1: Performance", International Journal of Turbo and Jet Engines, 2008, 25, 61-79.
[6]
W. Li, "The sudden-rising head effect in centrifugal oil pumps", World Pumps, 2000, 149(2000), 34-36.
[7]
W. Li, "Influence of the number of impeller blades on the performance of centrifugal oil pumps" World Pumps, 2002, 32–35.
[8]
M. Asuaje, F. Bakir, S. Kouidri and R. Rey, "Inverse design method for centrifugal impellers and comparison with numerical simulation tools", International Journal of Computational Fluid Dynamics, 2004, 18(2), 101–110.
[9]
G. Kergourlay, M. Younsi, F. Bakir and R. Rey, "Influence of splitter blades on the flow field of a centrifugal pump: Test-analysis comparison", International Journal of Rotating Machinery, 2007, Article ID 85024, 13 pages.
[10]
M. Shojaee, F. Boyaghchi and M. Ehghaghi, "Experimental study and three dimensional numerical flow simulation in a centrifugal pump when handling viscous fluids", IUST International Journal of Engineering Science, 2006, 17(3-4), 53-60.
[11]
M. Shojaee and F. Boyaghchi, "Studies on the influence of various blade outlet angles in a centrifugal pump when handling viscous", American Journal of Applied Sciences 2007, 4(9), 718–724.
[12]
V. Grapsas, F. Stamatelos, JS. Anagnostopoulos, and D. Papantonis, "Numerical study and optimal blade design of a centrifugal pump by evolutionary algorithms", In: 12th International Conference, KES 2008 Zagreb, Croatia, September 3-5, 2008 Proceedings, 26-33.
[13]
R. Spence and J. Teixeira, "A CFD parametric study of geometrical variations on the pressure pulsations and performance characteristics of a centrifugal pump", Computers & Fluids, 6 (38), 1243–1257.
[14]
K. Cheah, T. Lee, S. Winoto and Z. Zhao, "Numerical flow simulation in a centrifugal pump at design and off-design conditions", International Journal of Rotating Machinery, 2007, Article ID 83641, 8 pages.
[15]
K. Guleren and A. Pinarbasi, "Numerical simulation of the stalled flow within a vaned centrifugal pump", J. Mechanical Engineering Science, 2004, 425–435.
[16]
M. Asuaje, F. Bakir, S. Kouidri, F. Kenyery and R. Rey, "Numerical modelization of the flow in centrifugal pump: volute influence in velocity and pressure fields", International Journal of Rotating Machinery 2005:3, 244–255.
[17]
C. Boaling, Z. Zuchao, Z. Jianci and C. Ying, "The flow simulation and experimental study of low-specific-speed high-speed complex centrifugal impellers', Chinese J. Chem. Eng., 2006, 14(4) 435-441.
[18]
J. Anagnostopoulos, "Numerical calculation of the flow in a centrifugal pump impeller using Cartesian grid", Proceedings of the 2nd WSEAS Int. Conference on Applied and Theoretical Mechanics, Venice, Italy, November 20-22, 2006.
[19]
J. Anagnostopoulos, A fast numerical method for flow analysis and blade design in centrifugal pump impeller", Journal of computer and fluid, 2008, pp 284-289.
[20]
E. Bacharoudis, A. Filios, M. Mentzos and D. Margaris, “Parametric Study of a Centrifugal Pump Impeller by Varying the Outlet Blade Angle” The Open Mechanical Engineering Journal, 2008, 2, 75-83.
[21]
S. Weidong, Z. Ling, L. Weigang, P. Bing, and L. Tao, “Numerical Prediction and Performance Experiment in a Deep well Centrifugal Pump with Different Impeller Outlet Width”, Chinese Journal Of Mechanical Engineering, 2013, 1 (26).
[22]
R. Singh and M. Nataraj, “Parametric Study And Optimization Of Centrifugal Pump Impeller By Varying The Design Parameter Using Computational Fluid Dynamics: Part-I” Journal of Mechanical and Production Engineering (JMPE), 2012, 2(2), 87-97.
[23]
L. Zhou and W. Shi “Performance Optimization In A Centrifugal Pump Impeller By Orthogonal Experiment And Numerical Simulation” Advances in Mechanical Engineering, 2013, Article ID 385809, 7 pages.
[24]
M. Mentzos, A. Filios, M. Margarisp and D. Papanikas, “CFD prediction of flow through a centrifugal pump impeller,” 1st International Conference on Experiments/Process/System Modelling/Simulation/Optimization, 2005, Athens, 6-9 July, 1-8.
[25]
V. Yakhot and S. Orzag, " Renormalization group analysis of turbulence: Basic theory", Journal of Scientific Computing, 1986, 3-51.
Browse journals by subject