Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery

Odo Jude Emeka; Onyejekwe Ifeanyi; Anthony Chikwe; Angela Nwachukwu; Okereke Ndubuisi; Oguamah Ifeanyi; Obikaonu Agnes Chidiebere

doi:doi:10.11648/j.eas.20210602.12

Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery

Odo Jude Emeka, Onyejekwe Ifeanyi, Anthony Chikwe, Angela Nwachukwu, Okereke Ndubuisi, Oguamah Ifeanyi, Obikaonu Agnes Chidiebere

Published in Engineering and Applied Sciences (Volume 6, Issue 2)

Received: 16 August 2020 Accepted: 21 October 2020 Published: 23 April 2021

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

The use of metallic oxides in enhanced oil recovery in the initial stage seems to significantly enhance the productivity from a well by increasing the sweep efficiency, reduce interfacial tension, and reduce oil viscosity among other factors. However, in later stages of the life of the reservoir, it is observed that the technology brings adverse effects such as reduction in the permeability of the reservoir rock, which may cause decline in production and may lead to the abandonment of the reservoir, although there may be sufficient underlying hydrocarbon. This paper studies the extent of permeability alteration due to the aluminium oxide nano-powder, the total amount of recovery due to aluminium oxide nano-powder. It also compares the performance of aluminium oxide nano powder with other selected nano powders, which are silicon oxide and magnesium oxide. In the experiment, the Core Flooding System was used to simulate reservoir fluid flow in the constructed sand packs. The Enhanced Oil Recovery percentages as well as permeability changes were obtained. From the results, in comparison with traditional water flooding, aluminium oxide as well as silicon oxide and magnesium oxide gave high increase in recovery. However, aluminium produced the greatest recovery increase. A higher permeability change was given by aluminium oxide at higher concentration, while at lower concentration, aluminium oxide gave a lower permeability change.

Published in	Engineering and Applied Sciences (Volume 6, Issue 2)
DOI	10.11648/j.eas.20210602.12
Page(s)	41-48
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Aluminium Oxide, Enhanced Oil Recovery, Metallic Oxide, Permeability Alteration, Recovery, Sand Packs, Core Flooding System

References

[1]	Kapusta, S., Balzano, L. (2011). Nanotechnology Application in Oil and Gas Exploration and Production. Paper presented at the International Petroleum Technology Conference, 7-9 February, Bangkok, Thailand. p. 1-4.
[2]	Wikipedia. (2019). History of Nanotechnology. Retrieved from wikipedia.org: https://en.m.wikipedia.org/wiki/History_of_nanotechnology
[3]	Lau, H. C., Yu, M. (2016). Nanotechnology for Oilfield Applications: Challenges and Impact. SPE Paper presented at the International Petroleum Exhibition & Conference, 7-10 November, Abu Dhabi. p. 1-9.
[4]	Ogolo, N. A., Olafuyi, O. A., Onyekonwu, M. O. (2012). SPE Paper presented at the SPE Saudi Arabia Section Technical Symposium and Exhibition. 8-11 April, Al-Khobar, Saudi Arabia. p. 1-5.
[5]	Gao, C. (2007). Factors Affecting Particle Retention in Porous Media. Petroleum Engineering Department, Curtin University of Technology, Australia. p. 1-5.
[6]	Hogeweg, A. S., Hincapie, R., Foedisch, H., Ganzer, L. (2018). Evaluation of Aluminium Oxide and Titanium Dioxide Nanoparticles for EOR Applications. EAGE Conference and Exhibition 1-2 Copenhagen, Society of Petroleum Engineers.
[7]	Bayat, A. E., Junin, R., Shamshirband, S. (2015). Transport and Retention of Engineered Aluminium Oxide, Titanium Oxide and Silicon Oxide Nanoparticles Through Various Sedimentary Rocks Scientific Reports. p5.
[8]	Chen, H., Ding, Y., and Tan, C. (2007). Rheological Behaviour of Nanofluids. New Journal of Physics 10.
[9]	Vidyapeeth, P., Joob, B., Wiwanitkit, V. (2017). Nanotechnology for Health: A New Useful Technology for Medicine. p5.
[10]	Hashemi, N., Pereira -Almao. (2012). Transport Behaviour of Multimetallic Ultradispersed Nanoparticles in an Oil-Sand-Packed Bed Column at a High Temperature and Pressure Energy Fuels. p1645-1655.
[11]	Yang, J., Ji, S., Li, R., Qin, W., Lu, Y. (2015). Advances of Nanotechnologies in Oil and Gas Industries. New York SPE.
[12]	Hendraningrat, L., Shidong, L., Torsaeter, O. (2012). A Glass Micromodel Experimental Study of Hydrophilic Nanoparticles Retention for EOR Project. SPE Paper presented at the SPE Russian Oil and Gas Exploration and Production Technical Conference and Exhibition, 16-18 October, Moscow, Russia. p. 4-5.
[13]	Alexander, S. H., Rafael E. H., Hendrik F., Leonhard G. (2018). Evaluation of Aluminium Oxide and Titanium Dioxide Nanoparticles for EOR Applications. EAGE Conference and Exhibition 1-2 Copenhagen, Society of Petroleum Engineers.
[14]	Sun, X., Zhang, Y, Chen, G., Gai, Z. (2017). Applications of Nanoparticles in Enhanced Oil Recovery: A Critical Review of Recent Progress. College of Petroleum Engineering, China University of Petroleum (East China), Quingdao 266580, China. p. 4-13.
[15]	Odedele, T. O. (2014). Synthesis and Application of Nanomaterials in Enhanced Oil Recovery. SPE Paper presented at the SPE Nigerian Annual International Conference and Exhibition, 5-7 August, Lagos, Nigeria. p. 1.

Cite This Article

Plain Text BibTeX RIS

APA Style

Odo Jude Emeka, Onyejekwe Ifeanyi, Anthony Chikwe, Angela Nwachukwu, Okereke Ndubuisi, et al. (2021). Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery. Engineering and Applied Sciences, 6(2), 41-48. https://doi.org/10.11648/j.eas.20210602.12

Copy | Download

ACS Style

Odo Jude Emeka; Onyejekwe Ifeanyi; Anthony Chikwe; Angela Nwachukwu; Okereke Ndubuisi, et al. Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery. Eng. Appl. Sci. 2021, 6(2), 41-48. doi: 10.11648/j.eas.20210602.12

Copy | Download

AMA Style

Odo Jude Emeka, Onyejekwe Ifeanyi, Anthony Chikwe, Angela Nwachukwu, Okereke Ndubuisi, et al. Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery. Eng Appl Sci. 2021;6(2):41-48. doi: 10.11648/j.eas.20210602.12

Copy | Download

@article{10.11648/j.eas.20210602.12,
  author = {Odo Jude Emeka and Onyejekwe Ifeanyi and Anthony Chikwe and Angela Nwachukwu and Okereke Ndubuisi and Oguamah Ifeanyi and Obikaonu Agnes Chidiebere},
  title = {Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery},
  journal = {Engineering and Applied Sciences},
  volume = {6},
  number = {2},
  pages = {41-48},
  doi = {10.11648/j.eas.20210602.12},
  url = {https://doi.org/10.11648/j.eas.20210602.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.eas.20210602.12},
  abstract = {The use of metallic oxides in enhanced oil recovery in the initial stage seems to significantly enhance the productivity from a well by increasing the sweep efficiency, reduce interfacial tension, and reduce oil viscosity among other factors. However, in later stages of the life of the reservoir, it is observed that the technology brings adverse effects such as reduction in the permeability of the reservoir rock, which may cause decline in production and may lead to the abandonment of the reservoir, although there may be sufficient underlying hydrocarbon. This paper studies the extent of permeability alteration due to the aluminium oxide nano-powder, the total amount of recovery due to aluminium oxide nano-powder. It also compares the performance of aluminium oxide nano powder with other selected nano powders, which are silicon oxide and magnesium oxide. In the experiment, the Core Flooding System was used to simulate reservoir fluid flow in the constructed sand packs. The Enhanced Oil Recovery percentages as well as permeability changes were obtained. From the results, in comparison with traditional water flooding, aluminium oxide as well as silicon oxide and magnesium oxide gave high increase in recovery. However, aluminium produced the greatest recovery increase. A higher permeability change was given by aluminium oxide at higher concentration, while at lower concentration, aluminium oxide gave a lower permeability change.},
 year = {2021}
}

Copy | Download

TY  - JOUR
T1  - Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery
AU  - Odo Jude Emeka
AU  - Onyejekwe Ifeanyi
AU  - Anthony Chikwe
AU  - Angela Nwachukwu
AU  - Okereke Ndubuisi
AU  - Oguamah Ifeanyi
AU  - Obikaonu Agnes Chidiebere
Y1  - 2021/04/23
PY  - 2021
N1  - https://doi.org/10.11648/j.eas.20210602.12
DO  - 10.11648/j.eas.20210602.12
T2  - Engineering and Applied Sciences
JF  - Engineering and Applied Sciences
JO  - Engineering and Applied Sciences
SP  - 41
EP  - 48
PB  - Science Publishing Group
SN  - 2575-1468
UR  - https://doi.org/10.11648/j.eas.20210602.12
AB  - The use of metallic oxides in enhanced oil recovery in the initial stage seems to significantly enhance the productivity from a well by increasing the sweep efficiency, reduce interfacial tension, and reduce oil viscosity among other factors. However, in later stages of the life of the reservoir, it is observed that the technology brings adverse effects such as reduction in the permeability of the reservoir rock, which may cause decline in production and may lead to the abandonment of the reservoir, although there may be sufficient underlying hydrocarbon. This paper studies the extent of permeability alteration due to the aluminium oxide nano-powder, the total amount of recovery due to aluminium oxide nano-powder. It also compares the performance of aluminium oxide nano powder with other selected nano powders, which are silicon oxide and magnesium oxide. In the experiment, the Core Flooding System was used to simulate reservoir fluid flow in the constructed sand packs. The Enhanced Oil Recovery percentages as well as permeability changes were obtained. From the results, in comparison with traditional water flooding, aluminium oxide as well as silicon oxide and magnesium oxide gave high increase in recovery. However, aluminium produced the greatest recovery increase. A higher permeability change was given by aluminium oxide at higher concentration, while at lower concentration, aluminium oxide gave a lower permeability change.
VL  - 6
IS  - 2
ER  -

Copy | Download

Author Information

Odo Jude Emeka

Department of Petroleum Engineering, Federal University of Technology, Owerri, Nigeria
Onyejekwe Ifeanyi

Department of Petroleum Engineering, Federal University of Technology, Owerri, Nigeria
Anthony Chikwe

Department of Petroleum Engineering, Federal University of Technology, Owerri, Nigeria
Angela Nwachukwu

Department of Petroleum Engineering, Federal University of Technology, Owerri, Nigeria
Okereke Ndubuisi

Department of Petroleum Engineering, Federal University of Technology, Owerri, Nigeria
Oguamah Ifeanyi

Department of Petroleum Engineering, Federal University of Technology, Owerri, Nigeria
Obikaonu Agnes Chidiebere

Department of Petroleum Engineering, Federal University of Technology, Owerri, Nigeria

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Odo Jude Emeka, Onyejekwe Ifeanyi, Anthony Chikwe, Angela Nwachukwu, Okereke Ndubuisi, et al. (2021). Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery. Engineering and Applied Sciences, 6(2), 41-48. https://doi.org/10.11648/j.eas.20210602.12

Copy | Download

ACS Style

Odo Jude Emeka; Onyejekwe Ifeanyi; Anthony Chikwe; Angela Nwachukwu; Okereke Ndubuisi, et al. Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery. Eng. Appl. Sci. 2021, 6(2), 41-48. doi: 10.11648/j.eas.20210602.12

Copy | Download

AMA Style

Odo Jude Emeka, Onyejekwe Ifeanyi, Anthony Chikwe, Angela Nwachukwu, Okereke Ndubuisi, et al. Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery. Eng Appl Sci. 2021;6(2):41-48. doi: 10.11648/j.eas.20210602.12

Copy | Download

@article{10.11648/j.eas.20210602.12,
  author = {Odo Jude Emeka and Onyejekwe Ifeanyi and Anthony Chikwe and Angela Nwachukwu and Okereke Ndubuisi and Oguamah Ifeanyi and Obikaonu Agnes Chidiebere},
  title = {Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery},
  journal = {Engineering and Applied Sciences},
  volume = {6},
  number = {2},
  pages = {41-48},
  doi = {10.11648/j.eas.20210602.12},
  url = {https://doi.org/10.11648/j.eas.20210602.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.eas.20210602.12},
  abstract = {The use of metallic oxides in enhanced oil recovery in the initial stage seems to significantly enhance the productivity from a well by increasing the sweep efficiency, reduce interfacial tension, and reduce oil viscosity among other factors. However, in later stages of the life of the reservoir, it is observed that the technology brings adverse effects such as reduction in the permeability of the reservoir rock, which may cause decline in production and may lead to the abandonment of the reservoir, although there may be sufficient underlying hydrocarbon. This paper studies the extent of permeability alteration due to the aluminium oxide nano-powder, the total amount of recovery due to aluminium oxide nano-powder. It also compares the performance of aluminium oxide nano powder with other selected nano powders, which are silicon oxide and magnesium oxide. In the experiment, the Core Flooding System was used to simulate reservoir fluid flow in the constructed sand packs. The Enhanced Oil Recovery percentages as well as permeability changes were obtained. From the results, in comparison with traditional water flooding, aluminium oxide as well as silicon oxide and magnesium oxide gave high increase in recovery. However, aluminium produced the greatest recovery increase. A higher permeability change was given by aluminium oxide at higher concentration, while at lower concentration, aluminium oxide gave a lower permeability change.},
 year = {2021}
}

Copy | Download

TY  - JOUR
T1  - Effect of the Application of Aluminium Oxide on Recovery in Enhanced Oil Recovery
AU  - Odo Jude Emeka
AU  - Onyejekwe Ifeanyi
AU  - Anthony Chikwe
AU  - Angela Nwachukwu
AU  - Okereke Ndubuisi
AU  - Oguamah Ifeanyi
AU  - Obikaonu Agnes Chidiebere
Y1  - 2021/04/23
PY  - 2021
N1  - https://doi.org/10.11648/j.eas.20210602.12
DO  - 10.11648/j.eas.20210602.12
T2  - Engineering and Applied Sciences
JF  - Engineering and Applied Sciences
JO  - Engineering and Applied Sciences
SP  - 41
EP  - 48
PB  - Science Publishing Group
SN  - 2575-1468
UR  - https://doi.org/10.11648/j.eas.20210602.12
AB  - The use of metallic oxides in enhanced oil recovery in the initial stage seems to significantly enhance the productivity from a well by increasing the sweep efficiency, reduce interfacial tension, and reduce oil viscosity among other factors. However, in later stages of the life of the reservoir, it is observed that the technology brings adverse effects such as reduction in the permeability of the reservoir rock, which may cause decline in production and may lead to the abandonment of the reservoir, although there may be sufficient underlying hydrocarbon. This paper studies the extent of permeability alteration due to the aluminium oxide nano-powder, the total amount of recovery due to aluminium oxide nano-powder. It also compares the performance of aluminium oxide nano powder with other selected nano powders, which are silicon oxide and magnesium oxide. In the experiment, the Core Flooding System was used to simulate reservoir fluid flow in the constructed sand packs. The Enhanced Oil Recovery percentages as well as permeability changes were obtained. From the results, in comparison with traditional water flooding, aluminium oxide as well as silicon oxide and magnesium oxide gave high increase in recovery. However, aluminium produced the greatest recovery increase. A higher permeability change was given by aluminium oxide at higher concentration, while at lower concentration, aluminium oxide gave a lower permeability change.
VL  - 6
IS  - 2
ER  -

Copy | Download